Johnson-level-tool-mfg 40-6210 Bedienungsanleitung PDF herunterladen

Green Laser Technology™

PowerLine™ Magnetic-Laser “Sheave Alignment System”

Instructions

The PowerLine™ Sheave Alignment System aligns belts, pulleys, sheaves, sprockets, gear trains, rollers,

platforms, conveyors, and other plant equipment. Its purpose is to replace often times inaccurate and time-

consuming straightedge and string alignment methods currently in use. Compared to these older methods,

the PowerLine™ is easier, faster, and more accurate. With the PowerLine™, you will greatly reduce

downtime and belt failures. The new Green Laser Technology™ and reflective target system increases the

brightness of the laser line by 10 fold. This means that the system can be used in direct sunlight and at

longer distances.

Component Descriptions: The PowerLine™ Sheave Alignment System includes a laser line emitter and

three grooved targets. All components are especially rugged for long life and are shipped in a sturdy

storage case.

Laser Line Emitter: Its bottom machined surface mounts magnetically to the machined face of sheave,

gear, etc. It projects a 1/16” thick laser reference line over a wide angle. The projected reference line is

parallel to the machined bottom surface and offset from it by 0.312”.

Warning and Certification Label Bottom Surface is on Back Side

Laser Safety: Caution- Use of controls or adjustments or performance of procedures other than

those specified herein may result in hazardous radiation exposure.

The PowerLine™ emitter uses a laser diode with a maximum output power of less than <1 milliwatt @ 635

nm. The laser classification is Class II < 1mW @ 532nm with only minor precautions required. Never

stare directly into the laser transmitter or aim the laser into someone’s eyes. The PowerLine™ complies

with 21CFR parts 1040.10 and 1040.11.

Grooved Targets:

Level Vial Product Identification Battery Cap

Label On/Off Switch

5/16”

Excellent alignment is achieved when laser

line hits here on center of target groove. This

reference can be adjusted up or down to

compensate for sheaves with different thickness

by turning knob.

Initial knob setting is to

extend the magnet bottom

outward from the target

bottom by one full turn

(1/16”) so target groove

center is elevated 0.312”

off magnet bottom. Adjust

dow

n fr

Knob on to

0.312” 1/16”

1 2 3 4 5

Inhaltsverzeichnis

Seite 1 - Instructions

Green Laser Technology™ PowerLine™ Magnetic-Laser “Sheave Alignment System” Instructions The PowerLine™ Sheave Alignment System aligns belts, pulle

Seite 2

22 Three cylindrical grooved targets mount magnetically to the machined face of the companion pulley, sheave, gear, etc. to be aligned. The

Seite 3

33Using an inside caliper, measure the difference in endwall thickness between the two sheaves being aligned. The measurement can be easily taken u

Seite 4

44 User has option to turn sheaves every 90 degrees and check laser and targets. They should still show excellent alignment as long as the alignment

Seite 5

55 Supplied By: Laser Tools Co., Inc., 12101 Arch St., Little Rock, AR 72206, 501-562-0900, Fax501-562-0022 Web Site: www.Lasertoolsco.com, e mail

Kommentare zu diesen Handbüchern

Keine Kommentare

Johnson-level-tool-mfg 40-6210 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Werkzeug Johnson-level-tool-mfg 40-6210 herunter. Johnson Level & Tool Mfg. 40-6210 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Werkzeug Johnson-level-tool-mfg 40-6210